LAUNCH X431 Creade Elite 2-0 Bi-directional obd2 scanner All System car diagnostic tool ECU coding 31 reset Lifetime Free Update

The Link has several types in the link sale , Please select the correct version you need :

1. For VAG Brand

Including DEMO, OBDII, for Volkswagen, for Audi, for Bentley, for Skoda, for Bugatti, for Lamborghini, for SIAT, for Volkswagen Business

2. For BENZ Brand

Including DEMO, OBDII, for Benz, for Maybach, for SPINTER

3. For BMW Brand

Including DEMO, OBDII, for BMW, for mini and for Rolls-Royce

4. For GM Brand

Including DEMO, OBDII, for Buick, for Chevrolet, for Cadillac, for GMC, for Alpheon, for Ravon, for Pontiac, for Saturn, for Hummer, for Oldsmobile, for Holden, for Daewoo, for Workhorse

LAUNCH X431 Creader Elite V2.0 Supports Autoauth for FCA SGW

Fit for FCA vehicles with a secure gateway module (2017 and later For Chrysler, For Dodge, For Jeep, For Fiat, For Alfa Romeo, etc). Perform diagnostics and bi-directional control without using a bypass cable. In the US, FCA account registration is allowed via tablet. (Note: These models mentioned above need to be purchased se-parately in the mall. This code scanner for mercedes benz only supports For Mercedes-Benz, For Maybach, and For SPINTER vehicles. There is an annual $50 fee for Autoauth account, but the payment is charge-d by AutoAuth directly. LAUNCH is not involved in any tran-saction process.)

LAUNCH X431 Creader Elite V2.0 Supports All Systems Diagnose Function

All Systems Including : ABS System, Engine System, SAS System, TPMS System, IMMO System, Battery System, Oil Service System, SRS System, DPF System，Air Conditioning System，Transmission System..........

Full Diagnostic Function :

--read fault codes: read and decode the DTCs to identify where the fault location is;
--clear fault codes: erase the DTCs to turn off the MIL after repairs;
--retrieve ecu information: allows you to retrieve vehicle information;
--Graph live data stream: view the dynamic data stream to determine vehicle condition
--Freeze Frame: it will record the information of the vehicle running status at the moment when the fault occurs to confirm the fault.
--Vehicle information: such as Vehicle Identification Number (VIN), Calibration Mark (CALID) and Calibration Verification Number (CVN) .
--Online & Offline ECU Coding: generally used for cars after replacing second-hand parts, then it can work .
--Active Tester( Bi-Directional Control ): to test whether the actuators of each system are normal, for analysis
--Special Function: more than 31+ reset function , like airbag reset, AF Adjustment, DPF reset.........

LAUNCH X431 Creader Elite V2.0 Supports Online and Offline ECU Coding Function

* Component Matching
* Retrofit and Mo-dification
* Recode replacement parts to the car
* Perform a transmission quick relearn
* Program Vin into replacement PCM

Personalization: Adapt the codes to achieve personalized settings and improve vehicle comfort.

Disable Annoying Functions: such as lo-cking seat-belt warn-ing sounds, in-jector bu-zz sounds, daytime running light, auto start/stop, etc.

Unlock Hidden Functions: such as activate mirrors folding function, remove change speed li-mit, remote window control un-locking, adjust am-bient lighting brightness, etc.

Customize Car OE-Settings: such as re-trofit head-lamp, change tire size, retro-fit ba-ttery with different type, customize da-sh kits, etc

Component Matching: Write adaptive data to match various on-board modules after replacement.

LAUNCH X431 Creader Elite V2.0 Supports Active Tester( Bi-Directional Control ) :

* Powerful Bi-directional Control (Active Test) as a hot function for mechanic/workshop, can save you a lots of time and money as it sends a command to vehicle ECU to perform component test for checking ac-tuator's working status to quickly pinpoint problem parts without disa-ssembling the vehicle. By utilizing Bi-Directional Control let you quickly understand whether a specific system, component, or subsystem is operating normally. This function can significantly reduce the diagnostic effort, making it much easier to do time-consuming trouble-shooting. Having this bidirectional scan tool for mercedes benz by your side would greatly smooth workflow.

* More-Used Bidirectional Control/Active Tests Including:

Operate Mirrors, Turn the Wi-per ON/OFF, Turn ON/OFF Cooling Fan, Turn ON/OFF Head-lamp, Turn the Fu-el Pu-mp ON/OFF;
Turn On/Off the Sound Hor-n, Lock/Unlock Door, Roll Window Up/Down, Switch the Interior Lights ON/OFF, Open/Close the Sunroof;
In-jector Bu-zz Test, Modulate Throttle, A/C Com-pressor Acti-vation, Disable/Enable Transport Mode;
Activate Cooling System/ Test the Device Acce-leration/ Seat Ca-libration / All Wheel Drive Ca-libration/ Camera Ca-libration/ Head light Fitting/ Air Su-spension Height Ca-libration/ Test Door Lock Actuators/ In-let & Out-let Valve and a lot of functions waiting for you!

LAUNCH X431 Creader Elite V2.0 Supports 31+ Reset Function :

( pls note different reset function supports different cars , also supports some cars , not for all cars , pls contact us check the detailed car list , you also can check in the link directly : https://qcar.x431.com/qcar/#/pc/index?q=eyJsYW4iOiIxMDAyIn0%3D ）

The reset Function is in " Diagnose - Car Brand - Special Function "

1> Oil Reset Service

This function enables you to reset the oil service for the engine oil life system,which calculates an optimal oil life change interval depending on the vehicle driving conditions and weather events.
lt needs to be performed in the following cases:
1. lf the service lamp is on, run car diagnostics first for troubleshooting.Afterthat, reset the driving mileage or driving time, so as to turn off the servicelamp and enable a new driving cycle.
2. lf the service lamp is not on, but you have changed the engine oil or electric
appliances that monitor oil life, you need to reset the service lamp.

2> Electronic Parking Brake Reset

This function enables you to reset the brake pad after replacing the brake pad.lt needs to be performed in the following cases:
1.The brake pad and brake pad wear sensor are replaced.
2.The brake pad indicator lamp is on.
3.The brake pad sensor circuit is short, which is recovered.4.The servo motor is replaced.

3> Steering Angle Calibration

This function enables you to reset the steering angle,after replacing thesteering angle position sensor,replacing steering mechanical parts (such assteering gearbox,steering column, end tie rod, steering knuckie), performingfour-wheel alignment, or recovering car body.
To reset the steering angle, first find the relative zero point position for thecar to drive in straight line. Taking this position as reference,the ECU cancalculate the accurate angle for left and right steering.

4> ABS Bleeding

This function allows you to perform various bi-directional tests to check theoperating conditions of Anti-lock Braking System(ABS).
lt needs to be performed in the following cases:
1. When the ABS contains air.
2. When the ABS computer, ABS pump, brake master cylinder, brake cylinder,brake line, or brake fluid is replaced.

5> Gear Learning

This function enables you to perform tooth learning for the car, to turn off the MIL.
lt needs to be performed in the following cases:
1. After the engine ECu, crankshaft position sensor, or crankshaft flywheel isreplaced.
2. The DTC 'tooth not learned' is present.

6> IMMo Service

This function enables you to perform the anti-theft key matching function, sothat the immobilizer control system on the car identifies and authorizes remotecontrol keys to normally use the car.
lt needs to be performed in the following cases:
When the ignition switch key, ignition switch,combined instrument panel,ECU,BCM, or remote control battery is replaced.

7> Injector Coding

This function enables you to write injector actual code or rewrite code inthe ECU to the injector code of the corresponding cylinder，so as to moreaccurately control or correct cylinder injection quantity.
lt needs to be performed in the following cases:
After the ECu or injector is replaced.

8> Battery Maintenance System Reset

This function enables you to perform a resetting operation on the monitoringunit of vehicle battery, in which the original low battery fault information will becleared and battery matching will be done.
lt needs to be performed in the following cases:1. The main battery is replaced.
2. The battery monitoring sensor is replaced.

9> Diesel Particulate Filter (DPF) Regeneration

This function enables you to clear PM(Particulate Matter) from the DPF filterthrough continuous combustion oxidation mode (such as high temperatureheating combustion,fuel additive or catalyst reduce PM ignition combustion)to stabilize the filter performance.
lt needs to be performed in the following cases:
1. The exhaust back pressure sensor is replaced.
2. The PM trap is removed or replaced.
3. The fuel additive nozzle is removed or replaced.
4. The catalytic oxidizer is removed or replaced.
5. The DPF regeneration MlL is on and maintenance is performed.
6. The DPF regeneration control module is replaced.

10> Electronic Throttle Position Reset

This function enables you to make initial settings to throttle actuators andreturns the learned values stored on ECU to the default state. Doing so canaccurately control the actions of regulating throttle (or idle engine) to adjust theamount of air intake.

11> Gearbox Matching

This function enables you to complete the gearbox self-learming to improvegear shifting quality.
lt needs to be performed in the following cases:When the gearbox is disassembled or repaired.

12> AFS (Adaptive Front-lighting System) Reset

This function enables you to initialize the adaptive headlamp system.

13> Sunroof Initialization

This function enables you to set the sunroof lock off,closed when it rains,sliding / tilting sunroof memory function, temperature threshold outside the caretc.

14> Suspension Calibration

This function enables you to adjust the height of the body.
lt needs to be performed in the following cases:
1. When replacing the body height sensor， or control module in the airsuspension system.
2. When the vehicle height is incorrect.

15> EGR Adaption

This function is used to learn the EGR(Exhaust Gas Recirculation) valve afterit is cleaned or replaced.

16> Seats Calibration

This function is applied to match the seats with memory function that arereplaced and repaired.

17> Tyre Reset

This function is used to set the size parameters of the modified or replacedtire.

18> Coolant Bleed

Use this function to activate the electronic water pump before venting thecooling system.

19> AdBlue Reset (Diesel Engine Exhaust Gas Filter)

After the diesel exhaust treatment fluid (car urea) is replaced or filled up, ureareset operation is required.

20> NOx Sensor Reset

NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) inengine exhaust. lf the NOx fault is re-initialized and the NOx catalytic converteris replaced, it is necessary to reset the catalytic converter learned value storedin the engine ECu.

21> Ac System Initialization

AC system releam/initialization must be performed when the vehicle AC ECUor actuator is replaced or the ECu memory is lost.

22> High Voltage Battery Detection

This function is used for high voltage battery diagnosis and status informationdetection.

23> Windows Calibration

This function is used to perform door window matching to recover the ECuinitial memory, and recover the automatic ascending and descending functionof power window.

24> Language Change

This function is used to change system language of vehicle center console.

25> AF Reset

This function is applied to set or learn airlfuel rate parameters.

26> Transport Mode

To lower vehicle power consumption, user may perform the following operations: limit vehicle speed, not wake up the network for door open anddisable remote key etc. In this case, deactivating transport mode is needed torecover vehicle being normal.

27> StoplStart Reset

This function is used to open or close the automatic StartStop function viasetting the hidden function in ECU (The precondition is vehicle equipped withhidden function and hardware support).

28> Intelligent Cruise Control System Reset

This function is used to matching the intelligent cruise control module after it isreplaced or repaired.

29> Engine Power Balance Monitoring

This function is used to monitor crankshaft acceleration in the power stroke ofeach cylinder, to determine the relative power provided by each cylinder.

30> Gas Particulate Filter (GPF) Regeneration

This function is used to perform the GPF replacement or regeneration after the fuel consumption is increased and engine output power is reduced resultingfrom a long time service of the GPF.

31> Motor Angle Calibration

This function is used to perform the motor angle calibration when the rotorposition detected by the motor angle position sensor is different from theactual rotor field position.

LAUNCH X431 Creader Elite V2.0 Supports Full 10 OBD2 Function :

This scanner supports all 10 test modes for OBD-II cars which are great for daily repair work. The table below describes the purpose of each mode of operation:

1. Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)

2. Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.

3. Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.

4. I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.

5. Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform) display.

6. View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.

7.O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.

8.On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.

9.Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.

10.Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability.

The Other Functions that LAUNCH X431 Creader Elite V2.0 :

1. Maintain Information ( powerful & useful Function ) :

This function has a how-to for some special functions, which is about examples of operating special functions for real vehicles to help you learn the operation of the special functions; It also has Online Coding Help that will show you the steps for this function； And has Channel Information, it will show you how to do basic settings to make the channel return to its original normal value. All of this maintenance information can assist you to better resolving the vehicle's issue

2. DTC Library :

Allows you to retrieve the definition of the diagnostic trouble code from the abundant DTC database.

3. Display Real-Time Battery Voltage

If the charging system is not working properly, the battery will not get the proper charging voltage and it could go flat. This OBDII scanner can display the instantaneous voltage across the battery terminals in a graphical way. This helps you to get early warnings for possible battery and the charging system problems

4. Screenshot & Screen Recorder, Print Diagnostic Report

It is easy to you save the diagnostic data that you want , also the diagnostic report !
It also support print Diagnostic report , Scan the QR to Share first , then print .

LAUNCH X431 Creader Elite V2.0 Parameter :

• Screen Size: 4 inch Touch Screen
• Resolution: 480*800 pixels
• CPU: 4-core 1.3GHz processor
• RAM: 2GB
• ROM: 16GB
• WiFi: 802.11b/g/n 2.4GHz
• USB: TYPE-C
• OBD II Input voltage range: 9~18V
• Power up via: DC 5V data cable or Diagnostic cable through connection to vehicle's DLC
• Working Temperature: -10℃ to 45℃ (14℉ to 113 ℉)
• Storage Temperature: -20℃ to 70℃ (-4℉ to 158 ℉)

LAUNCH X431 Creader Elite V2.0 Packing List :